top of page

Buy Snowboard Wax

How to Choose Ski WaxWhy Wax? Wax is important for two reasons. It improves glide and protects your ski/snowboard base from oxidation that will degrade its properties and shorten its useful life. There are several forces that work against you:

buy snowboard wax

The ski/snowboard base is porous and will soak up wax; the wax will bleed out of the base as you ski and lubricate the surface to enhance your glide and protect your ski base against these frictional forces that can contribute to oxidation. But remember that you ski on your base, not your wax, the wax only lubricates. You need to scrape and brush all the wax off the ski base surface. Sharp snow crystals (especially for fresh snow) will dig into the surface wax and slow you down.

Here at Utah Ski Gear, one of our most frequently asked questions from our customers looking for tuning supplies, is what ski waxing iron they should buy. Of course, you can always find affordable, professional tunes at Utah Ski Gear. However, knowing how to wax is an essential skill for the frequent skier/snowboarder.

Damages to your base should always be promptly and professionally repaired. Given that your ski or snowboard has a PHANTOM application, a shop can repair the PHANTOM treated base just as you would normally with base welds and patches. Depending on the size of the repaired section, we recommend that PHANTOM be applied to the P-tex repair zone to maintain consistency across the entire surface area of the base.

As follows is the 'best, 'better' and 'good' scenario for preparing your bases for PHANTOM application. The 'best' path is to get your skis or snowboard stone ground at a shop to first remove all wax and dirt from the base before application; this allows maximum PHANTOM penetration. 'Better; is using a ski industry wax cleaner (we have found that these work, but don't remove 100% of wax in its entirety), or instead, using an alternative natural cleaner like olive oil, or hot water/dish soap before applying PHANTOM. 'Good' is applying PHANTOM over a waxed ski or board; we have tested this scenario, and we were pleased to find that PHANTOM still penetrates through wax into the depth of the base, and permanent on-snow performance is still good.

In a real-world application, the amount of surface area relative to the rest of the base in most repairs is relatively small, and you shouldn't experience a reduction in overall glide performance, but that will be subjective and relative with many possible variables: size, location, surface area of ski/snowboard in question, prior base quality. etc.

Maintaining snowboards and skis is easy to do yourself and it's a lot cheaper than taking your snowboard or skis to a specialist. Demon supplies everything you need for waxing and edge tuning. Show more

Skis and snowboards should be tuned every 5-6 times out on the mountains for the best performance and safety. Early season or manmade snow will pull the wax off your equipment and you may need to get your equipment waxed more frequently.

Most manufacturers prep their equipment to ski/ride off the shelf. If you purchase a snowboard or skis from us that require tuning, we are happy to offer a new ski/snowboard tune as a complementary service to your purchase.

While it's great to know the average lifespan of a snowboard, it's unrealistic to think anyone would track their days riding as a way to gauge when they'd need a new snowboard. And with so many variables controlling its longevity, days become irrelevant. The better solution is to know the signs of when to replace your snowboard - here's what you need to look for.

The average snowboard lasts between 150 to 200 days of riding. A snowboard's performance peaks during the first 75 to 100 days of riding, after which performance starts to gradually decline. The lifespan of a snowboard is largely influenced by the care, usage, location, and quality of the snowboard.

While it's great to know the average lifespan of a snowboard, it's unrealistic to think anyone would track their days riding as a way to gauge when they'd need a new snowboard. And with so many variables controlling its longevity, days become irrelevant.

With so many factors playing into the condition of a snowboard, it's difficult to gauge when you should replace it, especially if you're a beginner. And believe it or not, if you're new to snowboarding, this generally means your snowboard will have a longer lifespan.

The edges of a snowboard improve control when you're carving turns. Over time, the metal on the edges will start to erode and become blunt, which means they can no longer grip the snow as well as they used to.

The most important way to make your snowboard last is by taking care of it. Yeh, it's a bit trite, but we've all seen and been the people that throw their board in the trunk, rest heavy items on top of it, or leave it in less-than-ideal climates.

If the edge of your snowboard feels blunt to the touch or has burrs (little uneven pieces) of your snowboard, and it feels blunt or has "burrs" (little uneven pieces) you'll need to get your edges sharpened.

Where you start the season usually has a compounding effect on the condition of your snowboard at the end of the season. Here's a quick guide if you're getting your snowboard out of storage and tuned up for the season.

The age of a snowboard has no bearing on its condition, so as long as a snowboard was regularly maintained throughout the decade, and meets the usage limitations, generally 150-200 days of riding, then the snowboard could still be considered "good."

However, should the older board still has its pop and flex, and its edges are still sharp (or can be sharpened), you can use an older snowboard or buy one secondhand at a fraction of the price it would otherwise have cost.

If your snowboard hit the decade birthday or you're looking to buy one secondhand, you'll want to pay close attention to the 3 signs a snowboard needs replaced, detailed at the beginning of this article.

Your equipment is essential and can mean the difference between enjoying a day on the slopes or getting injured. Always ask your local snowboard shop for advice or help when you need it or when your board requires maintenance.

So, here are the things I look out for when assembling my own snowboard waxing kit. You can use this advice when you need to replace anything instead of having to buy a whole new kit altogether.

You need to acquire six primary products to assemble your DIY waxing kit at home. You would need a snowboard-compatible wax and cleaning solution, an iron, a scraper and structuring brush, a cloth for cleaning, and finally, a bag to put all this in.

Be careful to only buy your snowboard wax from known brands. This is because the wax will be in direct contact with the base of your snowboard, and inadequate wax products might end up doing more harm than good.

Whether you are waxing for racing purposes or just before you head out for a ski or snowboarding lesson with a coach, applying any universal wax will even give the average skier a noticeably better experience on the slopes.

Although you can take your board or pair of skis to the ski shop to get them professionally waxed, it is much less expensive to simply do it on your own. The wax can be applied in different ways. It takes about 12-15 grams to hot wax one pair of skis or one complete snowboard. Therefore, if you buy a 100 gram wax pack you can get about 6-8 hot wax applications out of it.

Refresh your essential snow gear while you're getting your skis or snowboard ready for the season. We have an excellent selection of helmets, goggles, and more from top brands. Shop online and pickup your items for free on your next shop visit.

The first step in tuning a snowboard is to sharpen the edges. The easiest way to sharpen edges is to use a file guide. A file guide will keep the file at the same angle for every swipe along the entire length of the board. Most file guides will have an angle indicator on them that you can set the degree of the edge for different riding styles. Complete as many swipes as needed but only swipe the file in one direction, not up and down.

Hot waxing your snowboard will bring out the best performance on your next trip and allow the base to glide much faster over the snow. A hot wax will penetrate further into the base and last much longer. Boards with sintered bases should only use hot wax because this base is much more porous and will absorb much of the wax. If a sintered base is not hot waxed regularly its performance will significantly depreciate. Applying hot wax will require an iron. Regular clothing irons might work but they will without a doubt be ruined. Clothing irons have steam holes that will get plugged with wax among other flaws for waxing purposes. Snowboard wax specific irons will work best because they will have certain heat settings for different kinds of waxes, they will be solid across the bottom with no holes for wax to get into and they will have a certain shape that will glide over a snowboard base.

Many snowboarders will prefer to use an all temperature wax in case of dramatic spikes in the weather from day to day. Temperature specific waxes will be used mostly by racers that will tune their board distinctively for the conditions the day of the race. Also a fluorinated wax will be best because it will penetrate in to the base better and the result is it will last longer and it will be faster.

Once all the extra wax has been removed you will want to use a Scotch-Brite pad or Fiber Tech that will help to remove any leftover wax. It will force more wax into the pores and will help to leave it really smooth and even. A pad for this purpose will often be included in a lot of tuning kits. A good way to save money on getting equipment to tune a snowboard is to buy it all together in a kit. Some will incorporate everything including the iron and they will have a case to keep it all together. Being able to tune and wax your own snowboard will also save you a lot of money. Having a shop do it for you will often cost around $20- $30. 041b061a72


bottom of page